A forklift swings a little wide coming out of an aisle and taps an upright. The driver sees a scuff and a shallow dent, decides it looks fine, and keeps moving. An hour later, another pallet goes up into that bay. Nobody writes anything down.
“It happens every day,” says Lee Daniels, account manager at Patterson Pope. “No matter how careful your drivers are, sooner or later a pallet or the forks are going to hit the rack.”
But the hit isn’t the real problem. A damaged rack going back into service unchecked is. A racking inspection is a regular check of your pallet racking for damage, overloading, and missing parts, so damaged bays come out of service before they fail.
Good pallet rack safety comes down to three habits:
- Walk the racking weekly or every shift
- Tag out any bay that’s been hit
- Bring in a qualified inspector for anything deeper
Below, we cover what OSHA expects, how often to inspect, what to check, and when damaged racking should be replaced instead of repaired.
What does OSHA require for pallet rack safety?
OSHA doesn’t have a standard written specifically for pallet racking. Instead, it cites rack hazards under its general materials storage rule, 1910.176, and the General Duty Clause. It also treats the industry standard ANSI/RMI MH16.1 as the benchmark.
In plain terms, stored material can’t create a hazard, and anything stacked or stored in tiers has to be stable and secured against sliding or collapse. Employers also have a general duty to protect workers from recognized hazards, and damaged, overloaded, or unanchored racking qualifies. MH16.1 fills in the details on design, load capacity, installation, and use (OSHA’s warehousing standards page lists it alongside 1910.176).
OSHA is also looking more closely at warehouses. Its revised National Emphasis Program on Warehousing and Distribution Center Operations took effect July 31, 2026, runs through 2031, and lists material handling and storage among its focus areas. That means more warehouse inspections, and a dented upright is hard to miss on a walk-through.
How often should pallet racks be inspected?
Most warehouses should have staff walk the racking at least weekly, and high-traffic operations often check every shift. Any hit should be documented right away, with the bay tagged out until someone qualified looks at it. “Most big places are doing that now,” Daniels says. “Somebody hits a rack, and it’s automatic: tag that whole bay out until we can get it looked at.”
Deeper periodic inspections belong to a qualified rack inspector or structural engineer, who can set a schedule based on your traffic and loads.
What should a pallet rack inspection checklist include?
A pallet rack inspection checklist should cover uprights, beams, connectors, base plates and anchors, load plaques, decking, and column guards. Walk the same route every time and check:
- Uprights and bracing: Dents, creases, bends, twists, or missing braces
- Beams: Impact damage and any bow or sag (a bowed beam usually means the bay is overloaded)
- Connectors and safety locks: Present and fully engaged
- Base plates and anchors: Twisted plates or anchors lifting out of the floor
- Load plaques: Posted, legible, and matched to what’s actually on the shelves
- Decking: Wire decks and supports seated and undamaged
- Column guards: Still anchored and intact
Base plates are the item most often missed, because the damage hides at floor level. “A lot of times you won’t see any damage on the upright itself, but the base plate might be twisted, and the anchor might be popping up,” Daniels says. An upright like that needs to be replaced and re-anchored.
What should you do when a racking inspection finds damage?
Unload and tag out the bay immediately if you find a buckled or creased upright, a creased or sagging beam, a base plate that’s lost its anchor, missing safety locks, or several damaged components in the same run.
Half measures don’t cut it. “Sometimes they’ll hit a beam, put a piece of tape on it, and say, ‘We’re just not going to use that level,’” Daniels says. “But really, if anything in that racking area has been hit, it all needs to come down.” Caution tape is a warning, not a repair.
That includes the neighbors. When an upright in one bay gets hit, unload the bays on either side too, because that upright is holding them up as well.
When should damaged pallet racking be replaced instead of repaired?
In most cases, damaged pallet racking should be replaced as soon as an upright or beam shows impact damage, like a dent, crease, or bend.
That’s especially true for roll-formed uprights, which aren’t built to take a hit. Replace the damaged component, and keep the surrounding section unloaded until the work is done. Any repair beyond that should be approved by the rack manufacturer or a qualified engineer.
Adding a column guard after the hit doesn’t count as a fix. It can help prevent the next hit, but it does nothing for an upright that’s already damaged.
So the real decision isn’t whether to replace. It’s what goes back in, and how you protect it. It’s time to opt for a new system, rather than swapping parts one hit at a time, when:
- Load ratings are unknown, or the manufacturer can’t be identified
- Components are mixed or discontinued, so capacities may not match
- The same bays keep getting hit, which points to a larger layout problem
- Corrosion or wear shows up across the system, not just in one spot
- Loads, pallet sizes, or lift trucks have changed since the rack went in
- Repair costs and downtime keep coming back
These signs pile up fastest in older buildings, and in racking that came with the lease: hand-me-downs from the last tenant, with no paperwork. Older systems also tend to sit lower than the building allows, leaving clear height you’re already paying for. A replacement is a good time to reclaim that space and rethink your warehouse’s layout.
Match the rack to the risk
Not every aisle needs the same rack. Roll-formed racking uses lighter-duty steel that’s open in the back, which keeps the cost down. Structural racking uses heavier-duty steel uprights and bolted-on beams built to take a hit (though it still needs to be checked after one).
“If it’s a drive-in rack, a push-back rack, or a freezer, where you know the rack is going to get hit, we really want structural,” Daniels says. “You don’t want to be replacing uprights in a freezer.” Nobody volunteers for that shift.
Roll-formed racking earns its place in narrow aisles with floor guide rails. When trucks are locked into their lane, they can’t reach the rack, and the less expensive upright does the job just fine. Our roll-form vs. structural racking guide covers the differences in more detail.
For most aging systems, selective pallet racking is the default replacement. If the re-plan opens up room for higher density, pallet flow racking or ActivRAC mobile racking may fit. (Here’s how ActivRAC compares to Pallet Mole.)
Prevention costs less than replacement
Once the rack is right, protect it. Floor-anchored column protectors stand up to a forklift in ways snap-on plastic guards can’t. End-of-aisle protectors shield back-to-back uprights where pallets get staged. Guide rails and guardrails keep trucks and loads out of the rack entirely.
“If there are 20 damaged uprights, we have to tear down everything around them, rent scissor lifts, and those aisles can’t be used for loading or unloading,” Daniels says. “If we can prevent that by putting column guards in ahead of time, it costs a lot less. It’s like preventative maintenance.”
Repair or replace: Quick answers
Can I keep using a rack if I tape off the damaged level? No. If any part of a bay has been hit, unload the whole bay, plus the bays sharing the damaged upright, until it’s inspected.
What are the risks of a bowing back beam? A bowed beam is overloaded, and that extra stress carries into the rest of the rack. Left alone, it can lead to a beam failure or even a collapse. Unload the bay right away, then lighten the load or install beams rated for it.
Is it safe to reuse racking left by a previous tenant? Have it inspected first. Unknown load ratings and mixed components are common in inherited racking, and they usually point toward replacement.
Can damaged racking ever be repaired? Any repair should follow guidance from the rack manufacturer or a qualified engineer. When in doubt, replace the component and keep the surrounding section unloaded until the work is done.
Let’s take a look at your racking
Patterson Pope’s warehouse storage team does visual safety walks: we’ll flag what needs to be replaced and recommend the right rack and protection for each area. A full engineered inspection still calls for a structural engineer, and we can help you plan around their findings.
If your racking has taken more hits than anyone wrote down, speak to a specialist or explore our full range of industrial storage solutions.


